Welcome to Skip to my Lou

As seen in the new book "Hand in Hand"

How To Build A Washers Game

It is time to move outdoors to play games and have some summer fun! This washers game will provide hours of fun!


How to build a washers game

Supply list for washers game:
1 – 4′ x 4′ x 3/4″ plywood finished on one side
2 – 1″ x 2″ x 12′ pine board
1 package EZ Drain drain tile sock
1 – 30″ x 1″ piano hinge
6 – 4″ closet flange spacers
1 box #8 x 2″ flat phillips wood screws
24 – 1/2″ to 3/4″ drywall or wood screws
12 – 21/2″ washers
Drill with a #2 phillips screw bit and a 3/32″ drill bit for pilot holes
4″ hole saw
150 grit sandpaper

Supplies needed to build a washers game

Washers Game Cutting Guide

Once all the pieces have been cut, drill the 4″ holes in each of the 18″ x 36″ plywood pieces. Build two games for friendly competition!!

The 3 holes are  placed 9″ from the edge and centered from the top down 7 1/2″, then 15 3/4″ from the top on center, and finally the third is 24″ from the top on center.  Mark a small “x” where the edge measurement intersects with the measurement from the top.  The center of this “x” is where you place the bit of the 4″ hole saw to cut out the holes.  Be sure to go slow and steady so that the wood does not splinter.  Lightly sand the holes once they have been cut out.

Washer Game DIY Plan

how to build a washers game

Apply trim to sides to create a finished edge.  Mount the 1″ x 2″ flush with the finished side of the plywood.  The edge pieces require 5 screws on each side and 3 screws along the top and bottom.

washers game plans step 3

To help keep the wood from splitting, drill pilot holes before screwing in the trim pieces.

Dewalt tools

My Husband loves to use his DeWalt quick connect impact driver chuck so that the phillips head bit and the drill bit used to drill pilot holes can be interchanged quickly.

how to build a washers game tutorial

Now we are ready to complete the holes for the washers.

plans to build a washers game

Cut EZ Drain mesh tube into 8 inch lengths. Sew along one end.

washers game plans

Pinch sewn end and sew across. Repeat for other side.

building a washers game

Turn inside out.

how to build a washer game steps

Pull the sock through the plastic flange spacer so the edge of the socks comes out to the  edge of the flange and fits evenly around the flange.  Center the sock and plastic flange  around the plywood hole.  Screw the flange tightly to the plywood.  Be careful that the screws pass through the sock materical and don’t catch it and bunch up.

washers game tutorial

How to build a washers game step 4

 

Measure where the hinged stand will fit by placing the 41/2″ block of 1″ x 2″ next to the edge of the trim at the top underneath side of the plywood board.  Then place the plywood stand next to the 1″ x 2″ block, and finally place the 18″ x 1″ x 2″ piece tightly next to the plywood stand.

Washers Game Plan Step 5

how to build an outdoor game

Fasten the 18″ x 1″ x 2″ piece onto the plywood board.  Don’t forget to drill  pilot holes  on each side about an 1″  to 1 1/2″ from the outer edge.

wooden game tutorial

washers game

Cut the 30″ piano hinge evenly in half with a hack saw.  Put the plywood stand and the 1″ x 2″ block back in place and take the 15″ piano hinge and place it evenly along the 18″ x 1″ x 2″ board and plywood stand.  Be sure the hinge is tight in the corner against each board.  Screw along the hinge with  the screws that were provided with the hinge.

washers game plans

washers game plans step 6

The small block can  be removed to allow the stand to fold, for easy storage.

washers game

Grab some washers and…

washers

let the games begin!

Thanks Lowe’s for challenging me to get outside and play! If you are looking for more fun ideas to enjoy the outdoors, Lowe’s has all the tools you need to be creative. Check out their Lowe’s Creative Ideas blog and be inspired! You can find Lowe’s Creative Ideas on Facebook and don’t forget to pick up a FREE Subscription to Lowe’s Creative Ideas Magazine. Their magazine is fabulous!

#lowescreator

As always my DIY supplies are from my go to store Lowes. Thanks Lowes for sponsoring this post!

 

LoadingUpdating...

Comments

Leave a Reply

Please note: Comments may not appear immediately.

© 2009 - 2014 Skip to my Lou