The oilcloth receipt wallet went together quickly and I was able to use up some scraps.

Supplies:

2 pieces cut 7 1/4" by 6 1/2"

2 pieces cut 2 1/2" by 6 1/2"

about 14 inches skinny double fold bias tape

miniature clothes pins

Fray Check

Elmer's Spray Adhesive (optional)

Teflon presser foot or masking tape to cover bottom of presser foot to keep oilcloth from sticking to presser foot (if necessary)

Instructions:

Slip bias tape around the 6 1/2 inch side of the 2" wide piece and stitch. It can hang off the edge, it will be trimmed when finished.

Place the two large pieces wrong sides together. I sprayed just a touch of Elmer's Spray Adhesive in the center to keep the pieces from slipping. Try to keep adhesive away from area that will be sewn. Place pocket pieces on each edge. Use miniature clothes pins to keep in place. Sew close to the edge all the way around the wallet, reinforcing when sewing over bias tape. Trim bias tape and place a few drops of fray check on ends. (I was going to just wrap the end of the bias tape to the inside before stitching, however it made it bulky.)

Ta Dah!

Note: I get my oilcloth from Oilcloth Addict! Be sure to check out her personal blog, ModernJune, for some fabulous oilcloth tutorials and great tips for sewing with oilcloth.

It would be easy to make a lot of these gifts assembly style.

I used  small 6"X 9" clipboards  found  at OfficeMax ($1.69). The notepads are 5" X 8" 50 sheet Jr. size writing pads, found at Wal-mart (6 notepads were only $2.50).

I tried these two ways:

Using Elmer's Spray Adhesive and Krylon Matt Finish

and using Mod Podge Paper Matte

First cut decorative paper to fit the clipboard.  For my clipboards 6" X 9" worked perfectly.  I took the extra time to make a template that fit around the top of the clip (a little bit of a pain).  I have also seen where there is just a rectangle shape cut to fit around the clip. My paper looked like this.

Paint the back of the paper with Mod Podge Paper (Matte) or spray with the Elmer's Spray Adhesive. If you are using spray adhesive also spray the clipboard. Cover the the clip with masking tape to keep it clean. Pay special attention to make sure which ever method used that the edges of the paper are completely covered. Working quickly, place the paper onto the clipboard. This is a bit tricky. It is okay to lift up and reposition until it matches all of the edges properly. Be careful not to stretch the paper. Smooth paper and make sure the entire piece of paper is secured.  When I had a spot along the edge that wasn't adhered, I lifted it slightly and added more glue.  Allow to dry at least 15 minutes before putting on top coat. Round off corners with scissors.

Give the top of the paper a light coat of Mod Podge Paper in matte  or two coats of spray matte finish.  I have to say I like the paper feel and look so I prefer the Krylon spray matte finish.

Glue a matching piece of decorative paper to the top of the notepad. Any glue will do.

To give the clipboard an extra nice touch I added a metal label holder. I taped them on with a piece of clear tape exactly where I wanted them and then my husband drilled holes in the metal clip so they could be attached with the brads included in the package.

I painted the metal holders and brads with gloss paint.  Open the clip as far as you can so you can attach the metal label holder and spread the brads apart on the back side of the clip.

Finished! I think I will put the recipient's name in the label holders.

Fabric Decorated office supplies (fun with pretty paper also)

Covered Thumbtacks

Decoupaged journal

Decorated notebook with a place for pens

Photo pencils (another great way to use kid photos for relatives)

Paper covered pencils (to download click on the pattern you like)

Magnets

Embellished paperclips

Decorated file folders and notepads

Altered Clipboards (notice the links she recommends)